Stay Cool WITH PARAGON Pools!

  • Call us now
    803-312-3103
  • Address :
    Columbia, SC 29209
  • Mon - Satday
    8am-6pm

CHLORINE, ITS PURPOSE AND APPLICATION?

Disinfection is the most important single factor in maintaining a swimming pool, which is safe and healthy. Chlorine is the most widely applied disinfecting agent.

WHAT IS CONDITIONER?

ALGAE... WHAT CAUSES IT?

When chemical levels are properly balanced, if phosphates levels are too high algae outbreaks will occur. Furthermore, algae will occasionally appear in a customer's swimming pool. Algae comes in a variety of forms, and appears for various reasons, meaning high phosphate levels or filtration problems.

Algae spores are everywhere: these microscopic single-cell structures are blown into the pool by the wind, washed into the pool by rainfall, or carried into the pool on swimmers' skin or bathing suits. Under the right conditions, tiny spores will bloom into those dreaded bright green, mustard yellow, or black discolorations.

Here are the key factors in algae growth:

Inadequate filtration will often lead to algae growth.

Water clarity depends on daily circulation and filtration. Anything that impedes water flow from the pool to the filter -- clogged skimmer baskets by too much vegetation (leaves, grass etc.), a dirty or damaged filter, a defective pump motor, or a failure to run the pump for an adequate amount of time each day -- will encourage algae growth. The first warning sign of a filtration problem is hazy or cloudy water. Left unchecked, cloudy water can quickly lead to a full-fledged algae bloom.

Algae can develop when little or no chlorine is present.

Sunlight, rainfall, temperature, number of swimmers and frequency of pool use affect the rate of chlorine loss. The lower the chlorine level, the more likely algae will bloom. Weekly super-chlorination, coupled with the application of conditioner or stabilizer designed to shield residual chlorine from the effects of heat and sunlight, helps ensure that there is always sufficient chlorine in the pool. Spas, which are often heated to temperatures well above 90 degrees, are especially susceptible to algae growth.

Algae loves a dirty pool!

Leaves and dirt left on the bottom of the pool for an extended period of time, not only promotes algae but also causes pool staining. As we all know in the Emerald coast area well water can leave stains on your walks leaves contain metal from well water, typically iron, which will cause stains if left for a period of time. The longer you allow leaves and other debris to sit on your pool floor, the more likely that you'll see algae, and staining. In an extremely dirty pool, algae will continue to bloom, even when the water chemistry is properly balanced.

WHAT CAN YOU DO TO PREVENT ALGAE?

Immediately after using the spa, adjust the valves so that the pool water will flow through the spa (if spa is on same filtration system as pool) when the filtration system is running. This will replenish chlorine-dissipated spa water with chlorinated water from the main part of the swimming pool.

Remove your pool cover one day per week (if covered) to allow the water to "breathe". For best results, uncover the swimming pool on your regular scheduled service day.

Periodically check to make sure the water is circulating adequately. Clean or backwash your filter if necessary.

Make sure the pump timer is set to run for at least 4 to 5 hours each day in the winter, and 10 or more hours daily during the summer months.

Make sure your filter is clean and your return lines have strong water flow.

Some spots of dead algae may remain on your pool walls, even after chemical treatment. Brushing the pool walls with a nylon bristle pool brush will remove dead algae, and help keep live algae from forming. A stainless steel brush should be used when dealing with black algae; it is made for this purpose and works great!!

HOW OFTEN SHOULD I RUN AND CLEAN MY FILTER?

Water clarity depends on three factors: proper chemical balance, adequate daily circulation, and quality filtration. Your swimming pool water needs the combination of these three variables to stay crystal clear, algae free, phosphate free and ready for swimming enjoyment. The filter is designed to trap small particles suspended in the pool water. These small particles are what make inadequately filtered pool water look hazy or milky.

A dirty filter can have a dramatic effect on circulation. As water passes through the filter, millions of tiny particles cling to the filtration elements. Eventually, these accumulated particles make it difficult for water to pass through the filter. A dirty filter can reduce pump efficiency by up to 80 percent. In other words, circulating your water for 10 hours a day when the filter is dirty is the equivalent of circulating the water for 2 hours a day when the filter is clean. Many times, a homeowner will find their water is cloudy and greenish, even though the chemical levels are fine, and the pump is running for an adequate amount of time each day. A dirty or damaged filter is usually the source of the problem.

Since filtration and circulation play such an important role in keeping your swimming pool water clear and properly maintained, we have included the following standard instruction for the three types of filter systems. Following these instructions will assist you in keeping your filter system working efficiently and effectively.

1.Sand Filters

Run filter system
Summer 8 to 10 hours per day during daylight hours
Winter 4 or more hours per day
(If pool looks cloudy, run filter until pool clears)- then go back to your regular schedule)
"Most filter manufacturers recommend backwashing after a clean filter has built up 5-10 PSI of pressure as indicated on the pressure gauge". Sand filters take 1 to 4 weeks. Over backwashing can lead to algae problems in the heat of the summer.

2. Diatomaceous Earth Filters Run filter system

Summer 8 to 10 hours per day (during sunlight hours)
Winter 4 hours per day, 4am to 8am
"Most filter manufacturers recommend backwashing after a clean filter has built up 5-10 PSI of pressure as indicated on the pressure gauge". D.E. filters typically build up these pressure levels in approximately 1 to 3 months. Over backwashing can lead to algae problems in the heat of the summer. Please perform major water exchanges in the cooler months." Report any major water exchanges to your local servicing branch immediately in order to ensure that the necessary additional chemicals are added.
Even with regular backwashing, D.E. filters accumulate debris and it is a good idea to have your filter dismantled and acid washed at least once a year. This affords an opportunity to check internal elements for wear and tear, and to ensure that the filter is working at peak efficiency.

3. Cartridge Filters

Run filter system
Summer 8 to10 hours per day during daylight hours
Winter 4 hours per day, 4am to 8am
"Most filter manufacturers recommend cleaning cartridges when filter has built up 5-10 PSI of pressure as indicated on the pressure gauge". Clean filter cartridges every 4-8 weeks, depending on dirt accumulation and filter size (The day before scheduled chemical service).
For those of you with cartridge filters, you can improve your filtering efficiency up to 50% by adding 2 coffee cans worth of Diatomaceous Earth to your filter. Adding the DE through the skimmer with the pump on, and stirring it in the skimmer until it is totally dissolved accomplish this. Each time you hose down the filter cartridges, you'll have to replenish the DE. Even with DE coating the cartridges, it's perfectly safe to hose down the filter elements on your lawn. DE is safe for grass and plants.

STAINING

Metals like copper and iron over time will discolor plaster or vinyl liner pools.. You may notice discoloration in your pool return or main drain. Although pools with dark surfaces may occasionally show signs of calcium or magnesium deposits, the real culprit to staining is dissolved metals. Dissolved metals like copper and iron can discolor a swimming pools surface and combine with calcium, magnesium and each other to leave various colorations. With higher hardness, more discolorations can occur.

One way to prevent metals from staining your pools surface between draining is to use a sequestering agent on a regular basis. Sequestering agents (metal removers) keep metals dissolved "in solution" so they have less tendency to deposit on your pools surface. Call our office. Our customer service representatives can offer additional information about stain preventing sequestering agents.

WHAT ARE THE ADVANTAGES AND DISADVANTAGES OF SOLAR COVERS?

Solar pool covers can be very effective in warming the pool water, thus extending the swimming season. Covering the pool in the early spring will allow you to use the pool sooner. Covering it again in the early fall will allow the pool to maintain a comfortable temperature longer, thus lengthening the swimming season.

We do not recommend using solar covers during the summer months. Water temperatures in excess of 90 degrees can deplete the chlorine levels and promote algae growth. The intense heat of the summer sun will also dramatically shorten the life of the cover.

We recommend that solar pool covers be removed completely for the entire service day. This allows the swimming pool to "breathe" and the chemicals to be more effective, If a swimming pool is covered when our service technicians show up to service the swimming pool, it is our policy to pull back the pool cover approximately four feet from the area where we are to dispense the chemicals. We will leave it uncovered and ask that is keep that way for at least the entire service day.

The disadvantage of a bubble cover is that they can blow off or away in heavy winds. Also, as you remove the cover the dirt either falls into the swimming pool or stays on the cover, meaning you have to spread the cover out and clean the cover as well as the pool. Taking the cover off and putting it back on can be a real chore. Sunlight and chemicals make the plastic brittle, causing the bubbles to collapse and sending little bits of blue plastic into the pool and circulation system. Bubble covers are only good for their thermal properties and should not be expected to last for more than 1-2 years.

Visit Our Show Room Today!
FREE, In Home Consultation
Advice 4 The Do it Yourselfers

803-312-3103